PULSE Showerspas 1015-2 Guida di Installazione Scaricare il pdf (Pagina 5)

Assembly

After installing your ShowerSpa, some assembly is required prior to use.

Handheld Holder Installation

1. Locate the desired mounting location of the handheld holder (6) and mark the holes. We recommend placing it near the height of

the glass shelf.

2. Drill ¼" holes through wall surface using a masonry bit. Drill slowly through wall surface to avoid cracking and chipping.

3. Make certain the opening in the handheld holder (6) tapers toward the ﬂoor when you mount it to the wall. Insert anchors (9) into

holes in wall and securely tighten handheld holder to wall with mounting screws (8).

NOTE—To adjust angle of handheld shower, loosen knob, gently rotate toward you or toward the wall, then tighten knob.

Connect The Handheld Shower

1. Insert rubber washer (11) into hexagon shaped end of handheld hose (7) and attach to threaded outlet on bottom of ShowerSpa.

DO NOT OVER-TIGHTEN.

2. Insert rubber washer (11) into tapered end of handheld hose (7) and attach to handheld shower (5). Place into handheld holder.

3. Place the female threaded end of the shower arm (3) over the male threads on top of the shower arm bracket (4). Hand tighten

until secure. The shower arm should swing freely from side to side for ideal positioning.

Connect The Shower Head

1. Check that the rubber washer (11) is in shower head (2) and screw shower head onto the shower arm (3).

Installation – New Construction

Extensive Remodel – New Finished Wall Surface

1. Prior to sheetrock, stub-out ½" hot and cold supply lines

beyond ﬁnished wall surface, 4" on center. For best results,

attach 90° brass ﬁttings (available at most hardware stores)

to the stub-outs maintaining ¼" – ½" of space between the

ﬁtting and ﬁnished wall. The open end of the 90° brass ﬁt-

tings should point down so the supply lines attach parallel

to the wall.

2. The height of the stub-outs is completely dependent upon

the desired mounting height of your Makena II ShowerSpa.

For a person 5'8" – 6'2" we recommend the stub-outs be 39"

from ﬁnished ﬂoor.

3. Before installation, make certain that water is COMPLETELY

TURNED OFF to both hot & cold supply lines of shower.

4. Mark the location of holes for the mounting brackets, mak-

ing sure brackets are level. For a person 5'8" – 6'2" tall, we

recommend putting the top bracket 65

8" from ﬁnished

ﬂoor height.

The bottom bracket should be positioned

exactly 23 ¼" below the top bracket with the holes plumb to

the upper bracket holes.

NOTE—Before drilling holes for the brackets, make certain

Showerspa will rest ﬂat against ﬁnished wall surface at the

desired mounting height with supply lines connected.

5. Drill ¼" holes through wall surface using a masonry bit. Drill

slowly through wall surface to avoid cracking and chipping.

Insert anchors and securely screw brackets to wall. Before

connecting hot and cold supply lines, hang ShowerSpa on

wall, check the height and make sure ShowerSpa is ﬂush

against wall with a secure ﬁt.

6. Connect hot and cold water supply lines to stub-outs—

DO NOT OVERTIGHTEN. Before mounting the ShowerSpa,

check ﬁttings to make sure they are secure. Turn on water

and check for leaks. When ﬁttings are leak-free, mount

ShowerSpa on wall.

7. OPTIONAL—Seal around body of ShowerSpa with a bead of

silicone. DO NOT SEAL BOTTOM.

Additional ﬁttings may be necessary depending on your speciﬁc situation.

The desired mounting height of ShowerSpa determines height of the ½" stub-outs. The stub-outs must be located at a height allowing sup-

ply lines to be connected and body of ShowerSpa to rest ﬂat against ﬁnished wall.

The mounting height may vary depending on several factors (i.e. location of supply lines, interference from ShowerSpa plumbing, personal

preference, etc.)

1 2 3 4 5 6 7 8

Commenti su questo manuale

Nessun commento

PULSE Showerspas 1015-2 Guida di Installazione Pagina 5

Commenti su questo manuale

Prodotti e manuali riguardandi Prodotti sanitari PULSE Showerspas 1015-2